Xinjiang's Largest Cogeneration Project Completed and Put into Operation, Filling the Heating Gap in Southern Xinjiang
IT Home, November 21 news: At 20:50 on November 20, Unit 7 of the Kashgar Huadian 2×660 MW cogeneration project—designed by China Energy Engineering Group East China Electric Power Design Institute and constructed by the Construction Group—passed its 168-hour full-load trial operation, marking the full completion and commissioning of Xinjiang's largest cogeneration project.
According to the official introduction obtained by IT Home, the project is located in Kashgar City, Xinjiang. It is a key project of the national "Two Joint Operations" integration initiative and a key project in Xinjiang's electric power development plan. It expands two 660 MW high-efficiency ultra-supercritical single-reheat indirect air-cooling units at the original site, with synchronous construction of flue gas desulfurization, denitrification, and dust removal facilities. During the pure condensing period, the units have a 20% THA deep peak-shaving capability, and the flue gas pollutant emission concentration meets ultra-clean emission standards.
The project adopts the "two units, one tower" and "chimney-tower integration" schemes. The main plant building is inspired by the design concept of "Tianshan Flying Snow," harmonizing industrial architecture with the urban landscape. At the same time, the project deeply integrates advanced technologies such as big data, the Internet of Things, and artificial intelligence to build two major platforms—intelligent power generation and smart management—creating a safe, efficient, green, and intelligent modern urban power plant.
After the project is fully put into operation, it will add 3200 million square meters of heating capacity, covering Kashgar City, Shufu County, and Shule County in the Kashgar region. It can provide a stable heat source for people's livelihood and electricity, effectively filling the heating gap in Southern Xinjiang and enhancing the end-of-grid power supply and peak-shaving capacity of the Southern Xinjiang power grid.
The project adopts high back-pressure heating technology, using the exhaust steam waste heat of the steam turbine for urban heating. During the heating period, the heat-to-power ratio exceeds 50%, achieving cascade utilization of energy and clean, efficient heating. The units use high-efficiency ultra-supercritical single-reheat parameters, with a designed average annual power generation coal consumption of approximately 269.25 grams/kWh, placing them at an advanced level among units of the same type. They are simultaneously equipped with low-nitrogen combustion, SCR denitrification, and electrostatic precipitation systems, with emission concentrations superior to national standards, achieving green and low-carbon operation while ensuring heating for people's livelihood.
The project is located in a high-intensity seismic fortification zone and adopts advanced seismic reduction and isolation design schemes. It is the first time in China that seismic isolation design has been adopted for a central control building of a thermal power plant. The coal bunker seismic isolation technology used in the side coal bunker is the first practical engineering application. At the same time, it is the world's first thermal power plant turbine hall to use a hybrid design of self-centering braces + buckling-restrained braces. It is the first to adopt key technologies for X-column steel-concrete composite and integral structures in ultra-high-intensity zones under the "two units, one tower" scheme. It is the first to use a four-corner connection for the 750kV outgoing lines of a 660 MW unit to save land area.
The project site has a risk of sand liquefaction, and the foundation soil and groundwater are highly corrosive to concrete and steel reinforcement. It also faces the challenge of controlling temperature cracks in mass concrete. The construction team solved these problems one by one through technological innovation: adopting a complete set of gravel pile reinforcement processes to eliminate liquefaction hazards, building a dual protection system of "impermeable concrete + anti-corrosion coating" to cope with the highly corrosive environment, innovatively applying layered inclined-surface pushing pouring, intelligent real-time temperature measurement, and integrated insulation and water-retention curing technology to control temperature cracks, and optimizing the support scheme through digital modeling, working condition simulation, and force calculation.
After the project is put into operation, it will further enhance the power and heat safety guarantee capacity of the Kashgar region, provide safe, reliable, clean, and low-carbon power and heat guarantees for the Kashgar region, and support the safe and stable operation of the Southern Xinjiang power grid.

Related Articles
- Harbin Institute of Technology Solves the "Longevity" Problem of Thermoelectric Devices, Converting Heat Energy into Electrical Energy
- One of Europe's Largest Nuclear Power Plants: Zaporizhzhia Nuclear Power Plant Restores External Power Supply
- The World's Highest-Altitude Grid-Connected Concentrated Solar Power Plant Put into Operation in Ngari, Tibet, Achieving Continuous Power Supply Day and Night
- Rumors Online of "Wild Monkeys Coming Down the Mountain to Snatch Mobile Phones at Xinjiang's Hemu Scenic Area"; Officials Respond "AI-Generated, No Monkey Habitats in the Area"
- Less Than 1mm Thick, Mobile Phone Piezoelectric Fans Expected to Be Commercialized; Southchip Technology Releases Driver Chip SC3606
- Mitsubishi Materials to Significantly Increase Production Capacity of Optical Communication Thermistors, Reaching 6 Times Last Year's Level by November 2027